Insulating Glass Silicone Sealant Machine Two Component Silicone Extruder Equipment

• Customization: Available
• Processing Speed: Other
• Processing Thickness: 3-19 mm
• Model NO.: ST 03
• Voltage: 220V
• Warranty: 1year
• Air Supply Pressure: 0.6~1.0MPa
• Machine Type: Insulating Glass Production Line
• Max.Dispensing Pressure: 20MPa
• Materia Drum: 55 Gallons(200L)
• Weight: Okg
• Video Outgoing-Inspection: Provided
• Core Components: Motor
• Key Selling Points: High Safety Level
• Ouurnt: 4~10L/Min
• Model: St03
• Glass Thickness: Other
• Mixing Ratio: 6:1~14:1
• Power: O
• Machinery Test Report: Provided
• Specification: 1100*950*1980mm
• Trademark: Eworld
• Origin: Shandong, China
• Production Capacity: 100%

Product Description

Manual Insulating Glass Silicone Sealant Spreading Machine Two Component Silicone Extruder Coating Equipment

 

 

Product Description

Brief Introduction

This type of manual insulating glass two-component silicone spreading equipment is a specialized sealant coating equipment for producing hollow curtain wall glass, achieving the one-time completion of mixing and coating of component A and B is particularly suitable for adhesive types that require strict proportioning accuracy. Suitable for high efficiency in doors, windows, curtain walls, and glass deep processing enterprises superior quality. The production demand for high pass rate assembly line operations. The rack adopts integral welding, adds gantry frames, and welds triangles to form a stable structure. To overcome the shaking of the cantilever beam during operation, pump B adopts double columns and double sealed pressure plates, completely solving the problem of oxidation and leakage of black component adhesive and optimizing pipeline design Solved the problem of slow flow rate in similar products.

Item.	Spec.
Model	ST03 Manual Insulating Glass Silicone Adhesive Sealing Equipment
Suitable for adhesive types	Silicone structural adhesive/Polysulfide adhesive/Polyurethane adhesive etc.
The working methods of the device	PLC control, fully pneumatic power
The working method of sealing injection valve	The standard configuration is an on-off valve, please specify when customizing.
Mixing ratio	6:1~14:1(Adjustable)
Diameter of A/B sealant	570mm/280mm
Materia drum	55 gallon (200L) 565mm
Suitable for adhesive with viscosity A	Below 300PA.S
Suitable for adhesive with viscosity B	Below 200PA.S
Lifting mode B plate pump	Single column cylinder
Lifting mode A plate pump	Double column cylinder
B pressure plate pump single reciprocating sealant	135ML
A pressure plate pump single reciprocating sealant	65ML
Transfer pressure plate pump pressure ratio B pres	20:1
Transfer pressure plate pump pressure ratio A pres	Select according to the viscosity of the sealant
Curing agent drum	5 gallon (20L) 285mm
Max. air consumption	0.5m³/min
Max. dispensing pressure	15~20MPa(Choose according to the viscosity of the sealant)
Output	4~10L/min
Air supply pressure	0.6~1.0MPa
Outside dimension	1100*950*1980mm
Weight	650kgs
Above Information are Eworld Glass Machine Standard Spec.  If customer want to change Spec. Please let us know.

Benefits & Advantages

 

The key components of this two-component coating machine are all from well-known brands, supplemented by key mechanism components made of high-strength and high-quality stainless steel refined through heat treatment technology, greatly improving the reliability and durability of the two-component coating machine and ensuring the excellent quality of the equipment. The two-component coating machine curing agent system is equipped with two filtering devices, which improve the mixing uniformity and curing performance of the two components. The system also has a high-pressure safety protection device for the pipeline, making operation and use safer. The system is a fully enclosed system that eliminates the mixing of air and prevents the curing agent from coming into contact with air to solidify, ensuring the stability of the medium flow rate. The mixing system of this machine adopts the internationally popular static reciprocating, belt mixer, imported mixing core rod, and a unique structure of one-way needle valve to make the mixing more uniform; The extrusion nozzle made of special elastic material makes the production of insulated glass more convenient, concise, and beautiful. The imported glue extrusion gun is easy to operate and has reliable sealing.

 

The Adhesive Supply System

The adhesive supply system is a closed system that prevents air and curing agents from coming into contact with air and solidifying, ensuring stable flow of the medium. This equipment integrates various tasks such as adhesive supply, proportioning, mixing, and spraying.

The Mixing System

The mixing system adopts a precision stainless steel mixer, with uniform mixing effect; it equipped with a specially designed one-way needle valve to ensure that the mixture does not reflux and prevent solidification inside the tube.

The Sealant Sealing Gun

Using a special alloy sealant gun, it is lightweight, agile, evenly mixed, easy to operate, and has zero leakage glue; Adjustable boost synchronous linkage proportioning mechanism, making proportioning adjustment very convenient.

The sealing gasket

The sealing gasket is made of imported Teflon material, which is reliable and durable.

 

The High-press Protection Valve

The imported high-pressure protection valve is sensitive to operation and safe to use.

Easy to Maintenance

Easy equipment maintenance, no need for additional lubricants, ensuring good sealing condition of the components

 

The Operation of the Two-component Sealant Sealing Equipment

 

1. Connect the air source

Turn on the source, adjust the pressure-reducing valve to 0.4Mpa~0.6Mpa, and check whether there is air leakage in the system. Then test run the following actions: (1) A pump lifts; (2) A pump inflates; (3) B pump lifts; (4) B pump inflates. Note: When the lifting cylinder is lifted, if the two cylinders are out of sync, please lower it to the origin and then operate again. 2. Place the A and B component glue barrels in place and align them with the axes of the A and B glue pumps. Take component A as an example: 1) Operate the manual rotary valve to lift pump A to high. During the lifting process, observe whether each pipeline is stretched too tight. 2) Place the glue bucket under the A-pump glue tray, open the glue bucket and the two-component glue machine accessories, turn the plastic bag out of the bucket, and take out the plastic sheet on the glue surface. 3) Slowly lower the pressure plate of pump A. When the pressure plate is put into the bucket, align it with the mouth of the bucket, and open the exhaust port of the pressure plate until the pressure plate touches the rubber surface. When all the gas in the pressure plate is exhausted and a small amount of glue overflows from the exhaust port, the exhaust valve can be closed. (The lift switch remains depressed) 4) Start the machine and try sealing: Turn on the air source switch of the main pump and press the glue gun switch until the air in pump A is exhausted and the glue at the muzzle is continuous. Use the same method to operate pump B. 3. Sealant sealing operation 1) Loosen the locking screw of the proportional pump on the proportional lever and adjust the inside and outside of the proportional pump to the required ratio. Only when the ratio of sealant A and sealant B reaches the normal value can the following operations be performed? 2) Set the selection knob to A and B pumps, align the outlet of the glue gun with the middle seam of the two pieces of glass, turn on the sealant gun switch, and move the sealant gun smoothly at an appropriate speed to fill the glass tank with the two-component sealant. Close the sealant gun when the sealing is complete. 4. Replace the rubber bucket 1) When the sealant in the sealant bucket is used up, switches A and B should be turned off immediately to stop sealing. 2) Turn on the A (or B) sealant pump inflation switch, select the A (or B) sealant pump lifting mechanism to the ascending position, and move the knob to slowly lift the pressure plate. At this time, attention should be paid: try not to leave the sealant barrel from the chassis until the pressure plate is completely separated from the sealant bucket, and turn off the inflation switch of the A (or B) sealant pump. 3) Remove the empty bucket, place the new sealant bucket in the working position, and repeat operations 3 and 4.

 

Know More

After you choose Eworld's glass machine, we will provide you with life-long guidance services, and each service will ensure that no less than 3 engineers will serve you, so that the difficulties you encounter can be solved in time.

 

Why choose us EWORLD machine?

 

   

   

3. We adhere to the business philosophy of integrity. Have a number of certificate certification, and put an end to fake certificates.

4. 7*24h online video guidance, we have a wealth of after-sales experience.

5. With our end users in more than 160 countries around the world, we can provide you with the most reasonable production advice.

 

 

Eworld has maintained world production and shipments.

Our products are leaving the factory and being sent to our customers.

 

 

 

 

Welcome to visit our factory! 

If you have plan to come to China and see our machines, please contact us at least 15 days in advance then we can arrange our schedule and arrange to treat you.
No matter which transport method you choose, we will pick up you.
If you have any questions, please feel free to contact us. 
24*7, we always be here!

 

Tips

 

 

294 comments prove that Eworld brand has been recognized and affirmed by many users in the international market. We prove to our customers with real data that Eworld brand wins customers with quality and creates more wealth for our customers with high-quality machines.

1.Question:Are you manufacture?
Answer: Yes,we are professional manufacture which have more than 5 workshops.

2.Question: How about the service?
Answer:
 
Deliver max within 15 days.

24 hours for after -sale service.
More than 12 years experience in this kind machine field.
Fluent English ,communication barrier free.

3. Question: What's the guarantee?
Answer:
Our guarantee is 18 months.
24 hour's technical support by email or calling.
English manual and video tutorial.
2 years quality guaranty for the machine (excluding the consumables).
We will provide the consumable parts at an agency price.
24 hours on line service each day, free technical support.

4. Question: Do you provide equipment operation training?
Answer: Yes. We can send professional engineers to the working site for equipment installation, adjustment, and operation training. All of our engineers have passport.

5. Question: If our price is higher than another company or factories?

Answer: Please check the different of the machine parts, service and guarantee, especially the machine inner electric parts, sometimes, if machines have breakdown, the most reason is the machine inner electric parts problem, but we use the famous and reliable parts for the machines inside.

6.Question: How long is the delivery time?

Answer: For standard machines, it would be 3-15 days; For non-standard machines and customized machines according to clients specific requirements, it would be 15 to 30 days.

7.Question: What is the payment?
Answer: Any payment method you want, such as L/C, T/T, D/P, West-union and so on.